A properly prepared jobsite allows for an efficient installation of cabinetry.
This list is to be reviewed and confirmed by the Customer/Builder to verify that the job site is ready for the cabinet installer to arrive and begin work.
A “buffer day” is recommended in the construction schedule to prevent long delays and/or extra cabinet install fees. In the event the cabinetry cannot be installed to completion at the scheduled time, a service charge will be added to the install fee and installation schedule may be delayed a week or more.
Cabinets must be confirmed to be on the jobsite.
Any site-specific “special circumstances” i.e., limited lighting, long distances to temporary power, muddy driveways, limited access or working hours, gate/lockbox codes etc., should be communicated sufficiently prior to installation date.
A customer representative is available to meet with the installer at the start of the job to give any jobsite specific instructions.
Full accessibility to the site is established, including gravel pad or clear driveway.
Clear access is available to all areas where cabinets are to be installed.
Cabinet installers are to be the only trade working in the specific area. Additional trades are slated only for work in the areas where cabinet installation is not scheduled to occur. This shall remain in effect for the duration of the installation schedule.
As a safety concern, homeowners are to stay out of the work area during construction. Additionally, it is difficult to work when someone is "hovering" in the work area. There will be ample opportunity to inspect the cabinets once the jobsite is clean and safe.
No appliances, plumbing fixtures or any other construction supplies / equipment are to be in the designated work area.
In the event of inclement weather, a covered area is available to set up tools and work.
The house is closed to outside elements. Heating and air system is operational to control temperature and humidity.
House should be capable of being locked after the cabinets are installed.
Drywall has been installed and completed, including taping and texturing.
Appliance model numbers, specifications and cut out dimension information to be printed and provided for the installer. TrueSource will provided the needed appliance information for appliances that are purchased from TrueSource.
Plumbing is properly located to accommodate cabinetry. Plumbing lines should be capped off with no valves or fittings to allow for minimal hole sizes. Stub out 8” if coming from floor. Stub out 2” if coming from wall. A large cutout will have to be made if the plumbing lines are coming from both the floor and the wall in the same cabinet.
Heating and air vents that come through cabinets should have sheet metal “boots” to direct air out, along with vent covers on site to allow the correct cut out size.
If cabinet install is requested before flooring, material will need to be provided by customer to raise cabinets to finished floor height. It is the customers responsibility to inform installer if cabinets need to be raised for flooring. It is recommended that the customer email TrueSource regarding cabinet / floor height so it can be added to install notes.
If flooring is installed before cabinets (new or existing), it is the responsibility of the customer to have floor protection installed. We recommend “Ram Board”. TrueSource is not responsible for any floor damage during cabinet install.
If flooring is installed after cabinets, quarter round is to be installed by flooring contractor or an additional charge will apply to return to install the quarter round trim.
Painting and general room trim can be installed before or after cabinet install. If painting is completed before cabinet install, it is likely that touch up paint will be needed after cabinet install. TrueSource is not responsible for touch up paint.
Exact Island location should be noted via dimensions from two locations to guarantee correct placement.
All cabinets and components (including trim) will be installed during initial installation schedule unless otherwise previously discussed.
Knobs/pulls to be onsite and will be installed during initial installation per the TrueSource hardware program. A clear explanation regarding hardware placement is to be provided to the cabinet installer (location of knob vs pull etc…). Written notes (diagrams if needed) are best to avoid any hardware install confusion.
All cabinets need to be inspected immediately. Any damage needs to be reported to TrueSource in writing within 24 hours of install (email to firstname.lastname@example.org). Please send pictures to document a concern. We cannot be responsible for damage created by a third party (other subs). A daily inspection by the customer is required for multi day installs.
Debris will be placed in a designated area. Debris removal is not included in the standard install price. A quote can be given if debris removal is needed.
In the event a jobsite condition impedes the installers ability to perform or complete work, additional charges may apply.
Thank you for your business!
Hours Appointments Required Available Appointment Times Monday - Thursday 7am - 7pm Friday 7am - 3pm
TrueSource Home Specialties 1935 Delk Industrial Blvd SE, Ste E Marietta, GA30067 Call: (770) 956-8899 Map to TrueSource